美國

制定機構名稱

標準編號

標準題名

1988

ANSI 美國國家標準協會 American National Standards Institute

ANSI/AIIM MS 43-1988

Standard for information and image management : recommended practice for operational procedures/inspection and quality control of duplicate microforms of documents and from COM

1988

ANSI 美國國家標準協會 American National Standards Institute

ANSI/AIIM MS 44-1988

Recommended practice for quality control of image scanners

1977年

ANSI 美國國家標準協會 American National Standards Institute

National electrical safety code

1993年

Association of American Railroads 鐵路科學研究機構

The Standard Code of Operating Rules

1984年 ASTM 美國機械工程師協會 American Society for Testing and  Materials ASTM 1984 Annual Book   of  ASTM  Standards

1969-1992

NACE=National Association of Corrosion Engineers美國國家腐蝕工程師協會

International book of standards

1985

充氣連結製造商協會(Expansion Joint Manufacturers Association

Standards of the Expansion Joint Manufacturers Association, Inc.

1980

美國『冷凍空調協會」標準

ASHRAE standard 90

Manual of acceptable practices : ASHRAE standard 90

美國『冷凍空調協會」標準

 

ASHRAE standard

1993年

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 13

SAE vehicle occupant restraint systems and components standards manual

1988年

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 1417

Fluid sealing handbook, radial lip seals SAE HS 1417 :/report of the Seal Committee, approved 1988

1988

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 1417

Fluid sealing handbook, radial lip seals SAE HS 1417 :/report of the Seal Committee, approved 1988

1992年

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 24192

Surface vehicle brake systems manual

1990

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 795

Manual on design and application of helical and spiral springs--SAE HS 795 : report of the Spring Committee

1990

美國自動車學會SAE = Society of Automotive Engineers

SAE HS 795

Manual on design and application of helical and spiral springs--SAE HS 795 : report of the Spring Committee

1994

美國自動車學會SAE = Society of Automotive Engineers

SAE HS-34

SAE ground vehicle lighting standards manual

1991年

美國自動車學會SAE = Society of Automotive Engineers

SAE manual on shot peening : report of the Surface Enhancement Division of the SAE Fatigue Design and Evaluation Committee, revised September 1991

1993年

美國自動車學會SAE = Society of Automotive Engineers

Introduction to all-wheel drive

1991

美國防火協會 (NFPA National Fire Protection Association)

NFPA 491M

NFPA 491M manual of hazardous chemical reactions.

1988

美國運輸協會(American Association of State Highway and Transportation Officials)

Standard specifications for movable highway bridges

1964年

美國齒輪製造商協會 AGMA(American Gear Manufactures Associations)

American standard

英國

BSI (British Standards Institution)

1990

BSI (British Standards Institution)

British Standard methods of test for soils for civil engineering

1987

BSI (British Standards Institution)

British standard code of practice for design of concrete structures for retaining aqueous liquids

1981

BSI (British Standards Institution)

BS 1-4551

Code of practice for site investigations

British Standard1-4551

IEEE標準

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

1986

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

ANSI/IEEE C57.117-1986

IEEE guide for reporting failure data for power transformers and shunt reactors on electric utility power systems

1978

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

ANSI/IEEE C57.13-1978

IEEE standard requirements for instrument transformers

1986

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

ANSI/IEEE C57.15-1986

IEEE Standard requirements, terminology, and test code for step-voltage and induction-voltage regulators

1984

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

ANSI/IEEE C57.95-1984

IEEE guide for loading liquid-immersed step-voltage and induction-voltage regulators

1990

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE C57.114-1990

IEEE seismic guide for power transformers and reactors

1989

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE C57.116-1989

IEEE guide for transformers directly connected to generators

1991

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE C57.125-1991

IEEE guide for failure investigation, documentation and analysis for power transformers and shunt reactors

1991

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE C57.19.01-1991

IEEE standard performance characteristics and dimensions for outdoor apparatus bushings

1989

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE C57.19.101

IEEE trial-use guide for loading power apparatus bushings

1974年

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE Std 259-1974

IEEE standard test procedure for evaluation of systems of insulation for specialty transformers

1990

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE-Std 1180-1990

IEEE standard specifications for the implementations of 8x8 inverse discrete cosine transform

1995

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Surge protection C62

1993

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Stationary battery

1991

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE guide for conducting a transient voltage analysis of a dry-type transformer coil

1986

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE guide for transformer impulse tests

1988

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE recommended practice for establishing transformer capability when supplying nonsinusoidal load currents

1988

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE standard test code for liquid-immersed distribution, power, and regulating transformers and IEEE guide for short-circuit testing of distribution and power transformers

1995

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Distribution, power, and regulating transformers

1995

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Electric machinery

1993

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Electricity Metering :/C12

1993

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Engineering in safety, maintenance and operation of lines (ESMOL).

1995

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Circuit breakers, switchgear, substations and fuses

1997

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

IEEE recommended practice for electric systems in health care facilities

1994

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Power capacitors

1995

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Protective relaying systems

1994

美國電子電機工程師協會(Institute of Electrical and Electronics Engineers

Roadway lighting equipment : C136

DIN

德國工業標準(Deutscher Industrie Nornen)

1980

德國工業標準(Deutscher Industrie Nornen)

DIN-Farbenkarte : system der DIN-Farbenkarte fur den 2-Normalbeobachter

1995

德國工業標準(Deutscher Industrie Nornen)

DIN-Katalog fur technische regeln

1989

德國工業標準(Deutscher Industrie Nornen)

DIN-Katalog fur technische regeln

1988

德國工業標準(Deutscher Industrie Nornen)

Beton und stahlbeton : bemessung und ausfuhrung

1995

德國工業標準(Deutscher Industrie Nornen)

Circuit breakers, switchgear, substations and fuses

1981

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 125

Informationsverarbeitung

1932

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 13

Normen der Elektrotechnik fur Installationsmaterial

1978年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 111

Normen fur Vermessungswesen

1982年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 188

Normen uber laborgerate und Laboreinrichtungen

1931年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 2

Schaltzeichen und schaltbilder

1981年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 4

Stahl und Eisen : Gutenormen

1981年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 155

Stahl und Eisen : Gutenormen

1998年

德國工業標準(Deutscher Industrie Nornen)

DIN-Taschenbuch 111

Vermessungswesen : Normen

ISO

ISO 國際標準化組織 International Organization for Standardization

1990

ISO 國際標準化組織 International Organization for Standardization

International Organization for Standardization. ISO catalogue. Supplement

1995年

ISO 國際標準化組織 International Organization for Standardization

ISO catalogue

加拿大

CAN/BNQ 1941-501-M-89

CAN/BNQ 2501-052-M-86

CAN/BNQ 2501-054-M-86

CAN/BNQ 2501-058-M-88

CAN/BNQ 2501-060-M-86

CAN/BNQ 2501-070-M-86

CAN/BNQ 2501-090-M-86

CAN/BNQ 2501-092-M-85

CAN/BNQ 2501-110-M-86

CAN/BNQ 2501-130-M-88

CAN/BNQ 2501-135-M-88

CAN/BNQ 2501-170-M-86

加拿大國家標準

MPIF Standard

MPIF=Metal Powder Industries Federation

1993-94

MPIF=Metal Powder Industries Federation

Standard test methods for metal powders and powder metallurgy products

Materials standards for metal injection molded parts 1993-1994ed

澳洲

1994

Concrete structures

INTERNATIONAL

1987-1993

Cost Accounting Standards Guide no185-249

1970

扣件規範

Fastener standards

1975年

真空元件

Vacuum Components